10.10.10.1 Router Login: How to Access Your Admin Panel

10.10.10.1 is a private gateway address used by a range of devices, most notably MikroTik routers, along with various portable LTE routers, captive-portal hotspot systems, and custom or enterprise network setups. A close neighbor, 10.10.1.1, belongs to the Temp Stick sensor’s setup page, so double-check which address your device actually uses. It is less common than 192.168.1.1, so if you have landed here, your device likely falls into one of those categories. This guide covers how to log in, the credentials to try, and what to do when the page will not load.

How to Log In to 10.10.10.1

1. Connect your phone or computer to the router, over Wi-Fi or with an Ethernet cable. You must be on the router’s own network, since 10.10.10.1 is a private address.
2. Open a web browser such as Chrome, Firefox, Edge, or Safari.
3. Click the address bar at the top of the browser, the bar that shows the web address. Do not use the search box, and take care with the digits, since it is easy to mistype the repeated tens.
4. Type http://10.10.10.1 and press Enter.
5. If a security warning appears, continue past it. It is safe on your own network.
6. Enter the username and password when the login page loads.

Username and Password

Because several device types use this address, the login varies. These are the most common combinations.

Device	Username	Password
MikroTik (older)	admin	(blank)
MikroTik (RouterOS 7+)	admin	(set at first login)
Many others	admin	admin

On MikroTik routers, the classic default is the username admin with no password, so you leave the password field blank. Newer RouterOS versions have no default password and prompt you to create one on first login. On other devices using this address, admin/admin is the most common combination.

The definitive source is the label on your device, especially for portable LTE routers and provider-supplied units, which often print a unique password there. The login is case-sensitive.

Which Devices Use 10.10.10.1?

This address is not tied to one mass-market brand. It shows up most often on:

• MikroTik routers, in certain default configurations.
• Portable and LTE routers, including some travel and mobile hotspot devices.
• Captive-portal and hotspot systems, where 10.10.10.1 hosts a login or voucher page rather than a full admin panel.
• Custom and enterprise networks, where an administrator chose the 10.10.10.x range deliberately.

If 10.10.10.1 does not open, your device most likely uses a more common address such as 192.168.1.1 or 192.168.0.1. Note that 10.10.10.1 and a 192.168 address are on separate subnets, so one will not respond in place of the other.

How to Change Your Wi-Fi Password

For routers with a standard web interface at this address, changing the Wi-Fi key follows the usual pattern.

1. Log in at 10.10.10.1.
2. Open the Wireless or WLAN settings section.
3. Find the Wi-Fi name (SSID) and the password field, sometimes labeled Pre-Shared Key or Passphrase.
4. Enter your new password and save or apply the change.

On MikroTik’s RouterOS, wireless settings live within its more advanced interface, either the WebFig web interface or the WinBox application, under the Wireless section, which offers far more control than a typical home router.

After saving, devices reconnect using the new details. Use a password of at least 12 characters with no personal details. Our full guide on how to change your Wi-Fi password covers the usual routers.

What to Do If 10.10.10.1 Will Not Load

Confirm this is actually your gateway. Check your actual address:

• On Windows: press Windows + R, type cmd, and run ipconfig. Read the “Default Gateway” line.
• On a Mac: open System Settings, then Network, select your connection, and check the Router field under TCP/IP.
• On a phone: open your Wi-Fi network details and look for the gateway or router field, or use our guide on how to find your router’s IP address.

Whatever appears there is the one to use. It may be 192.168.1.1, 192.168.0.1, or another address.

Check the digits. The address is 10.10.10.1. Enter it in the address bar with digits only, no spaces or missing dots.

Make sure you are connected to the router. A VPN, guest network, or mobile data will all stop the address from loading.

Try a wired connection or another browser. Ethernet is steadier for settings pages, and a private window rules out a cached page. If it still will not open, work through our guide on what to do when you cannot access the router web interface.

How to Reset the Router to Factory Settings

A factory reset erases everything: the Wi-Fi name and password, the admin password, and all settings. Reset only when locked out.

1. Find the recessed Reset button on the device.
2. With it powered on, use a pin or paperclip to press and hold for about 10 to 15 seconds, until the lights change.
3. Release and wait for the device to restart.
4. Log in with the default credentials for your device.

MikroTik routers also offer more advanced reset options, including holding the reset button during power-up to reach a backup system, which is useful for recovery. Check MikroTik’s documentation for your specific model.

Wrapping Up

Logging in at 10.10.10.1 means connecting to the router, typing the address into your browser, and signing in, most often with admin and a blank password on MikroTik units, or admin/admin on other devices. Because this address appears mainly on MikroTik, portable, and custom setups rather than mass-market routers, the label on your device is the most reliable source for the exact credentials. If the page will not load, confirm it is actually your gateway, since many routers use a more common address like 192.168.1.1. Do not confuse it with 10.10.100.254, which is the setup address for a solar inverter Wi-Fi stick rather than a router.