Ruckus Router Login: Access Your Device
Login address
192.168.0.1
Opens your router's admin login page. Works only on your own network.
Ruckus, now part of CommScope, makes business-grade wireless access points and switches, often found in offices, hotels, and newer homes built with commercial gear. The classic default login is the username super with the password sp-admin, at 192.168.0.1, which differs from the admin/admin most consumer brands use. Newer Ruckus Unleashed devices are set up a little differently. This guide covers both.
How to Log In to a Ruckus Device
- Connect your computer to the Ruckus device, over its Wi-Fi or with an Ethernet cable.
- Open a web browser such as Chrome, Firefox, or Edge.
- In the address bar, type 192.168.0.1 and press Enter. On Ruckus Unleashed systems, you can also use unleashed.ruckuswireless.com.
- If a certificate warning appears, proceed past it, covered below.
- Enter the username and password. See the next section.
Default Username and Password
| Device type | Login address | Username | Password |
|---|---|---|---|
| Most Ruckus devices | 192.168.0.1 | super | sp-admin |
| Ruckus Unleashed | unleashed.ruckuswireless.com or 192.168.0.1 | super | sp-admin |
The standard Ruckus default is super as the username and sp-admin as the password, both case-sensitive, so type them exactly. This is the credential most Ruckus access points and controllers revert to after a factory reset.
The IP address, username, and password are also printed on a sticker on the device, which is the most reliable source, especially since some models and pre-configured units differ. If you moved into a home that came with Ruckus equipment already installed, check for that sticker or ask the builder, since the credentials may have been customized.
Setting Up Ruckus Unleashed
Ruckus Unleashed is a controller-free system where the access points manage themselves, and its first-time setup works differently from a simple login.
For initial configuration, connect to the access point’s default setup network, which appears as an SSID named something like Configure.Me-XXYYZZ. Then browse to unleashed.ruckuswireless.com, where you are prompted to create your network and define your own admin credentials. From that point on, you log in with the credentials you created, not the factory default.
If your device does not broadcast a Configure.Me network after a reset, it may not be running Unleashed firmware, in which case you connect directly and access 192.168.0.1 with super and sp-admin.
The Certificate Warning Is Normal
Ruckus devices use a secure connection with a self-signed certificate, so your browser will warn that the connection is not private. This is expected on your own device. In Chrome, click Advanced and choose to proceed to the address. In Edge, click Details, then choose to continue to the webpage. It is safe on your own network.
How to Change Your Ruckus Wi-Fi Name and Password
Once logged in, you manage your wireless network from the dashboard.
Find the wireless or WLAN settings section, select the network you want to edit, and update the network name (SSID) and the password or passphrase. Save the change, and your devices will need to reconnect with the new details. The exact menu layout depends on whether you are running Unleashed, a ZoneDirector controller, or a standalone access point. For the general process, see our guide on how to change your Wi-Fi password.
How to Reset a Ruckus Device
If the credentials do not work and you are locked out, a factory reset restores the defaults, most likely super and sp-admin. Ruckus devices often use an extended reset process.
- With the device powered on, press and hold the reset button for about 30 seconds.
- While still holding it, unplug the power and continue holding for another period, then restore power while holding, following the extended reset process for your model.
- Alternatively, use the simple approach for your specific model: many just need the reset button held for several seconds until the lights change.
- After resetting, log in with super and sp-admin, then set your own credentials.
Because a reset disconnects an Unleashed device from its online setup, you configure it again from scratch afterward.
One security note: change the default credentials after setup. The super and sp-admin defaults are published widely, and keeping them leaves your device exposed, so set a strong password as part of securing your network.
Conclusion
Logging in to a Ruckus device usually means going to 192.168.0.1 and entering super and sp-admin, the business-grade defaults that differ from the consumer admin/admin. If you have a Ruckus Unleashed system, you set your own credentials during the unleashed.ruckuswireless.com setup and use those instead. Expect a certificate warning, which is normal, and change the default credentials once you are in, since super and sp-admin are widely known.
Frequently asked questions
What is the default username and password for a Ruckus router?
The default is super as the username and sp-admin as the password, at 192.168.0.1. Both are case-sensitive. This is what most Ruckus devices revert to after a factory reset, though the credentials are also printed on the device's sticker.
What is the default Ruckus IP address?
The most common default is 192.168.0.1. Ruckus Unleashed systems can also be reached at unleashed.ruckuswireless.com during and after setup. If neither works, check your router's device list for the address assigned to the Ruckus unit.
How do I set up a Ruckus Unleashed access point?
Connect to the access point's default setup network, named something like Configure.Me-XXYYZZ, then browse to unleashed.ruckuswireless.com. You will be prompted to create your network and set your own admin credentials, which you then use to log in from then on.
Why does my browser warn about the Ruckus connection?
Because Ruckus devices use a self-signed certificate for their secure connection, which browsers do not automatically trust. This is normal on your own device. Click Advanced in Chrome, or Details in Edge, and proceed to the page.
I moved into a home with Ruckus equipment. What are the login details?
Try super and sp-admin at 192.168.0.1, and check the device for a sticker with the credentials. If they were customized during installation, ask the builder or previous owner. If you cannot recover them, a factory reset restores the defaults but erases the existing configuration.
How do I reset a Ruckus device?
Hold the reset button, often using an extended process of about 30 seconds while power cycling, depending on the model. After the reset, log in with super and sp-admin and reconfigure the device. An Unleashed device will need to be set up again from scratch.